KF 300

Cement based adhesive for ceramic and gres porcelain tiles C1TE

Cement based adhesive suitable for the installation of medium size ceramic, gres porcelain tiles and moisture stable natural stones on both floors and walls in internal and external areas.

Consumption: 2-5 kg/m²
Color: White
Package: Paper bags 25 kg, Plastic bags 5 kg
Pallet: 1350 kg, 720 kg

Description

  • KF 300 cement-based adhesive is suitable for:
    • fixing coverings such as:
          • ceramic tiles, single fired, double fired, medium sizes
          • ceramic mosaic tiles
          • humidity stable marble and natural stone
    • applications on horizontal or vertical surfaces such as:
          • internal areas, wet areas like shower rooms and WC
          • external areas, balconies, etc.
          • medium traffic floors
    • application on various substrates like:
          • properly cured concrete and cement screeds
          • non-absorbent substrates (after suitable primer application)
          • plaster and masonry mortars
          • cement boards and gypsum boards (after suitable primer application)
  • Form: powder
  • POT life: > 6 hours
  • Open time: 30 minutes
  • Adjustability time: ≈ 20 minutes
  • Walkability: after 24 hours
  • Grouting on wall: after 10 - 12 hours
  • Grouting on floor: after 24 hours
  • Application temperature: from +5°C up to +35°C

Substrate preparation:

The substrate has to be compact, clean, free of grease, oil, laitance and any substances which may compromise the adhesion of KF 300. The minimum tensile strength of the substrate must be at least 1,5 N/mm².
On absorbent substrates like concrete, cement screeds etc. especially on hot and/or windy days saturate well the substrate with water and remove excess with appropriate toll like sponge. For additional information refer to the Technical Data Sheets of the relevant products.

Preparation of the mix:

Mix the content of the paper bag containing KF 300 (25 kg) with 6 – 6.5 liters of clean and fresh water by means of appropriate electrical stirrer at low speed for at least 3 – 5 min, until a uniform mortar free of lumps is obtained. During hot periods and in general, it is recommended to avoid direct sunlight exposure of the materials (in powder or liquid form) before use, otherwise the working time is reduced. In any case avoid mixing by hand.

Application:

The tiles are placed on the still fresh adhesive bed, by applying firm pressure, in order to ensure full contact between the tiles and the adhesive. The open time of KF 300 in normal temperature and humidity conditions is 30 minutes. Unfavorable weather conditions like contact with strong direct sunlight, drying and/or hot wind or a very absorbent substrate may reduce open time significantly. For this reason it is important to check if the adhesive has formed a superficial ‘skin’. If such incident occurs, remove the adhesive from the substrate and reapply it, before applying the tiles. Small corrections must take place 30 minutes after tile application. Surfaces tilled with KF 300 should not be exposed to rain, strong sun or frost for at least 24 hours.

Grouting:

Grouting can take place 12 - 24 hours after the tile application. For grouting joints up to 10mm width it is recommended to use of NOVAGROUT F. For rectified tiles or when the requirement is for very smooth grout surface, NOVACOLOR GLASS can be used. For wide joints of 5 - 20mm NOVAGROUT G. For areas where resistance to strong chemicals is required like in example kitchen benches it is recommended to use the epoxy grout NOVAGROUT EPOXY. For additional information refer to the Technical Data Sheets of the relevant products.

Recommendations:

Avoid using KF 300:

  • In cases where the substrate and environment temperature is less than+5°C or higher than +35°C
  • In a thickness higher than 10mm
  • On substrates like metal, wood or surfaces like polyurethane, acrylic and similar paint or coatings (use NOVACOL 2K ELASTIC)
  • On PVC, asphalt membranes and in general materials which polymerize in the long run
  • For bonding humidity sensitive marble and natural stones
  • On friable or not properly cured substrates
  • Over existing expansion joints
  • Under direct sunlight and/or strong wind

Also note the following:

  • Never exceed the maximum recommended quantity of mixing water
  • Protect the tiled surface from rain and frost for the first 24 hours
  • For tiles of total surface over 900 cm² the double-spreading (buttering) technique of adhesive is always recommended
  • Do not add cement, lime, gypsum or other binders or substances which may affect the mortar characteristics
  • Application should be performed by professional skilled workers

Cleaning:

Tools, buckets, tiles etc. can be cleaned with fresh and clean water as long as KF 300 is still fresh. After hardening occurs, cleaning can take place by mechanical means.

Legal Notice:

The technical data and recommendations included or listed are the outcome of laboratory measurements combined with our current knowledge and expertise. All information and specifications should in any case be considered as indicative. The Company makes every effort to ensure the accuracy of the information provided herein. Product specifications are subject to change without notice and may differ from product images. Due to printing and application procedures, the colors displayed here should be considered as indicative. In particular, variations in materials, substrates and on-site application conditions are such that no warranty can be given or implied reference to the suitability of the materials for trading or use for a particular purpose and conditions of any given project. Anyone interested in using the product must ensure beforehand that the product is suitable for the intended use and in any case, the user is solely responsible for any outcomes associated with the use of product. Among other things, the Company is not responsible for any normal wear or tear from environmental or any other unsuitable conditions. We reserve the right to revise or change the data herein without prior notice. Restrictions and disclaimers apply to the extent permitted by applicable law. The Company has a Technical Support Department, which has exclusive responsibility for providing technical advice and solutions, addressing relevant issues. Requests to the Technical Support Department are addressed and answered, only in writing. For the latest and valid version of the Technical Data Sheet, the user of the material must refer to our website www.novamix.gr.